Home > HAND TOOLS > TRADESMAN TOOLS > HVAC TOOLS
Choose a sub category:
HVAC TOOLS
Sort By:
1
Malco CB Replacement Cutter Bit Malco 18F Fixed Folding Tool Wiss WC5L Crimper Blade 1-5/8 in D Jaw
Mill type cutter bit for HC1 (373.8515) and HC2. Tool with 3/8" (9.5 mm) & 1" (25.4 mm) depths. Folding seams are formed from two steel halves, permanently joined together. Handy sight holes assure proper depth alignment. Longer folding tool assures a more uniform fold. Length 18". Wiss Crimper Blade, 1-5/8 in Jaw, Galvanized Steel Jaw, Non-Slip Cushion Grip Handle, 10 in Overall Length, For crimping Round Metal Pipe to Create a Male Fitting End
Wiss WC5S 5-Blade Hand Crimper Wiss WT1 Cable Tie Tensioning Tool Wiss WS3 HVAC Hand Seamer
Wiss Hand Crimper, 5-Blade, Forged Steel, Wiss, 1-1/4 in Jaw Width, 1-1/4 in Jaw, Cushion Grip Handle, Gray Handle, 9-1/4 in Overall Length, For Joins Corrugated, 22 Gauge Round or Square Sheet Metal Pipes of the Same Size Wiss Cable Tie Tensioning Tool, Heavy and Light Duty Nylon Cable Tie, 7-1/2 in Overall Length Wiss HVAC Hand Seamer, Steel, Wiss, 18 ga Mild Steel Metal Gauge Capacity, 3 in Jaw Width, 1-1/4 in Jaw, Forged Steel Jaw, 1/4 in Increments Graduation, Cushion Grip Handle, Steel Handle, Gray Handle, 8-3/4 in Overall Length, Matte, Black, Used to Produce a Permanent Tight Fitting Seam in 18 ga Sheet Metal
SEAMER HAND OFFSET 3 INCH     NOTCHER HAND 30DEG 8-3/4IN    SEAMER HAND STRAIGHT 6IN
Wiss Hand Seamer, 3-1/4 in Jaw Width, Offset Handle, 9 in Overall Length, 1/4 in Depth Markings, 1-1/4 in Maximum Seam Depth, For working in confined areas Wiss Hand Notcher, 13/16 in Length of Cut, 30 deg V-Notch Cut, Non-Slip Cushion Grip Handle, Gray Handle, 8-3/4 in Overall Length, Forged Steel Wiss Hand Seamer, 6 in Jaw Width, Straight Handle, 9-1/4 in Overall Length, 1/4 in Depth Markings, 1-1/4 in Maximum Seam Depth
Redline S9R Hand Seamer Malco HC1 Hole Cutter
Redline Hand Seamer, Steel, Redline, 0.035 in Aluminum Metal Gauge Capacity, 9 in Jaw Width, 2 in Jaw, Die-Cast Zinc Jaw, 1/4 in Increments Graduation, Soft-Touch With Non-Slip Handle Insert Handle, Steel Handle, Red/Black Handle, Nickel Plated, For Making Angle Bends for Aluminum Roof Flashing, Coil Stock or Fascia Distinctive gold Bits, Bearings and Pivot Pin signify the longest lasting, fastest cutting, easiest adjusting solution for cutting holes in sheet metal. Hole Cutters quickly install into the chuck of any corded or cordless drill as small as 1/4" (6.4 mm). Lightweight aluminum frames make this accessory extremely portable for a variety of hole cutting applications in sheet metal including 20-gauge (1.02 mm) galvanized steel; HC1 Hole Cutter is adjustable for making 2 to 12" (51 to 305 mm) diameter holes.
   
 
1